** Once the motor is free, cut the 4 wires connected to the motor. ** Move the motor’s belt over to the side and remove the 3 flat-headed screws that mount the motor. You might want to put these away carefully so that you get the plastic clips on the correct sides when you put it back together. One on each side is screwed through a plastic clip thing. ** Remove two screws on each side of the bracket to access the bottom bracket that holds the motor. ** Remove the entire bracket assembly with the screws on the top of the bracket. ** Remove the connector from the back of the cassette tape bracket. Since they are all different positions and there are slots so you don’t put them in backwards, it’s not really necessary to mark them or anything like that. ** After carefully opening up the unit, you have to disconnect 5 connectors – 4 from the big circuit board and one two-position connector from behind the transformer. ** There are about 15 screws on the bottom of the unit that need to be removed including one that is on the little “ledge” on the back of the 4-track. Here are some hints if you’re looking to do this repair yourself: I popped in the new motor, soldered the 4 wires into place and put everything back together. I must say that Studio Sound Electronics’ service is wonderful. The motor was $9.95Īnd shipping to California was just under $5. I decided to order a replacement from Studio Sound Electronics. I placed 12-volts on the motor and yup, no movement. I found from the information on their site that it was a 12-volt Mabuchi motor. But I finally found a place in Indiana called Studio Sound Electronics that carries the exact replacement. After taking out the bracket and looking at the motor, I did a quick Google search on the part number printed on the motor’s label (which proved not as fruitful as I thought it might be). I noticed that the motor underneath the cassette tape bracket seemed like it wasn’t moving when perhaps it should. I decided to open her up and poke around a bit. I decided to check out some old 4-track tapes recently and noticed that when I pressed play, rewind or any of the other tape transport buttons that the appropriate light would come on for a few seconds, some clicking was heard but it pooped-out. It was so handy having this setup to try out new gear and record that the Tascam almost never was powered down. Recorded many a Xome tracks on the beast and eventually set it up so that the output of the 4-track was plugged into the soundcard on my computer. It worked flawlessly when I first got it. I was fortunate enough to pick up a used Tascam Portastudio 424 MKII about 4 years ago on Craigslist.
Tascam 424 mkii manual manual#
P/NO : MFL61543970ENGLISHOWNER'S MANUALPortable CD Cassette RecorderMODELLPC14 (LPC14)Please read this manual carefully before operating your set and retain it for future 1LPC14-LGERA-Cover-ENG.indd 1 2010.2.4 10:51:13 AM2010.2.4 10:51:13 AM.
Tascam 424 mkii manual license#
WM-EX621AEP ModelUK ModelE ModelChinese ModelTourist ModelSERVICE MANUALCASSETTE PLAYERManufactured under license from Dolby LaboratoriesLicensing Corporation.“DOLBY” and the double-D symbol a are trademarksof Dolby Laboratories Licensing Corporation.SPECIFICATIONSModel Name Using Similar Mechanism WM-EX610Tape Transport Mechanism Type MT-WMEX610-162Ver 1.0 2001. ġ2“AM” “FM1”“FM2”“OFF”332112FULLEMPTYPRESETRADIOON/OFF/BANDHOLD12345OPENXBSTUNINGRQ-SW48VDIRREV WDHOLDXBSRADIOON/OFF/BANDTUNING45VOLUMEVOLUMEË231DIRFWDREV213123RADIOTAPE“ ”“ ”LRINSTALL ABATTERY.1 Stereo headphones(RFEV718P). Switzerland All rights reservedInstruction manualBedienungsanleitungManuel d’instructionsManuale d’istruzioniManual de instruccionesManual de instruções. RAUTOREVERSE CASSETTE TAPE WITHUSB OUTPUT TO ENCODE TAPE AUDIOTO ELECTRONIC FILES VIA PC.PST-100ENCRAUDIO VIDEOis a registered Trademark of Roadstar S.A.
Tascam 424 mkii manual Bluetooth#
0 kommentar(er)
